What're your opinions concerning How to Install a Bathtub?
Installing a bathtub isn't exactly rocket science, yet it does call for strong plumbing, carpentry, and often, tiling skills. Replacing an old bathtub with a new one is likewise a moderately difficult job. If the old tub is easily easily accessible, the task can relocate immediately; if you have to open a wall surface to get rid of the old bathtub as well as position the new bath tub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will need a helper to move out the old bathtub as well as embeded in the new one. Make sure you have qualified yourself for the task as well as are comfortable trying it. As opposed to hiring a service provider to take control of a halfway-completed project, it is better to consider employing one prior to you begin. Chances are you might need a specialist plumber to make tube links.
This post will certainly assist you set up a new tub in your shower room if you have actually currently bought a new tub and don't require to transform the arrangement of your previous water pipelines.
Your devices and product checklist must make up the following:
Planning for the Installment
First of all, the supporting structure provided with the bathroom should be fitted (if called for) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is very important to make certain that if the tap features a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps unit to avoid strain on the tub.
Fit the versatile faucet ports to the bottom of the two taps using 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its final placement.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you should do is disconnect the water system. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be quite bothersome as a result of the limited access that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a towel all set for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipelines have been eliminated, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing compound.
Prior to moving on to fit the brand-new faucets, compare the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Utilizing the two wooden boards under its feet, position the bathtub in the needed placement. The wood boards are handy in evenly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four small factors.
The next objective is to ensure that the bath tub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the bathtub up until the spirit level reads degree.
To mount taps, fit all-time low of the furthest versatile faucet port to the proper supply pipeline by making a compression sign up with; then do the same for the various other tap.
Switch on the water system and inspect all joints and brand-new pipework for leakages and tighten them if required. Load the bath tub as well as additionally examine the overflow electrical outlet as well as the typical electrical outlet for leakages.
Ultimately, deal with the bath paneling as defined in the producer's user's manual. Tiling and also securing around the bath tub ought to wait until the tub has been utilized a minimum of when as this will resolve it right into its final position.
Fitting New Touches
If the tails of the new taps are plastic, after that you will need a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will require minimizing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin guaranteeing that the washers remain in area between the faucet as well as the sink. Protect the faucet in position with the supplier given backnut. Once the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap adapters. The previous type ought to be attached to the tap finishes first, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bath satisfies the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to crack a stiff seal, triggering the water to permeate the wall between the bathroom as well as the tiling, causing complications with wetness and feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your fixtures and also installations. They are offered in tubes and cartridges, and can sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to securing, to permit the movement experienced when the bathtub remains in use. The sealer can crack fairly early if you do not consider this activity before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise easily offered on the market. It is recommended to fit the tiles making use of water-resistant or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our topic on How to Install a Bathtub. Thanks for taking time to read our blog post. Be sure to set aside a second to distribute this blog post if you liked it. We appreciate reading our article about How to Install a Bathtub Yourself.
Stress-free? Call now!